SUNLU AMS Heater review: in-place drying for the original AMS
At a glance
An original-AMS upgrade for reducing spool transfers, provided all loaded materials tolerate the chosen cycle.
The setup
- SUNLU AMS Heater for original Bambu AMS; not a standalone dryer
- Uses the supported AMS spool positions
- 35–70°C setting range
Why consider it
- Less movement between the feeder and a separate dryer
- Installation can be approachable on the intended hardware
What to weigh up
- Mixed materials require compatible heat limits
- The lid becomes heavier and operation less passive
- Fan sound can matter at a desk
SUNLU’s AMS Heater is an upgrade decision for an original AMS you already own. It can reduce the need to unload the working set for drying, but it also makes every roll left inside part of the same heating decision.
Read the entire loaded set before selecting a preset
A mixed ABS-and-PLA load was reported to deform PLA and jam feeders. The practical lesson is to include every loaded material and spool in the compatibility check, even when the drying cycle is intended for only one of them. Do not treat the selected material on the display as protection for everything else inside.
The lid becomes part of the daily routine
The heavier lid and manual exhaust management are meaningful tradeoffs for the convenience of in-place drying. Consider whether you can comfortably open the upgraded unit and attend to its documented controls in the location available. Installation praise alone does not answer those everyday questions.
If you frequently remove incompatible rolls anyway, compare that work with a separate dryer before choosing the upgrade. The humidity-display guide helps interpret the chamber reading; it cannot confirm that every loaded spool has finished drying.
Pros & Cons Analysis
Based on supplied customer reviews and verified product documentation
Pros
- Keep filament loaded in the original AMS. In-place drying reduces transfers between the feeder and a separate dryer. It is most useful when the existing AMS already fits the printing workflow and moving rolls is the main inconvenience.
- An approachable fit on the intended hardware. Installation and controls can be straightforward with the specified AMS arrangement. Confirm the exact feeder generation; this advantage does not validate adaptations to a different unit.
Cons
- Every loaded material must tolerate the cycle. A shared heated space can deform a less heat-tolerant filament or spool left beside another material. Check the limits of all loaded rolls, rather than choosing settings only for the one that needs drying.
- A heavier lid adds handling work. Lid support and manual exhaust management become part of the routine. Keeping spools loaded is convenient, but operation requires more attention than an ordinary unheated lid.
- Fan sound can intrude at a desk. High-pitched sound or cycling may be distracting even when drying is useful. Noise tolerance varies, so consider workspace placement before treating the upgrade as unobtrusive.
An AMS upgrade starts with the loaded set
Consider this heater when leaving rolls in the original AMS saves enough handling to justify the heavier lid and extra management. Incompatible material mixes weaken that case.
Check the whole installation, not only the selected preset.
The heater supports my exact AMS generation.
Every roll remaining inside tolerates the selected cycle, including its spool.
I can manage the documented lid and exhaust routine in this location.
The fan sound and access suit the space where I work.
If you regularly remove rolls to separate their cycles anyway, compare that effort with a standalone drying arrangement.
Frequently Asked Questions
Is the AMS Heater compatible with every AMS generation?
Compatibility here is limited to the documented original AMS setup. Check the exact heater and feeder generation before ordering.
Technical Specifications
| Product type | AMS heater accessory |
|---|---|
| Reviewed configuration | SUNLU AMS Heater for original Bambu AMS; not a standalone dryer |
| Host feeder compatibility | Original Bambu AMS; other generations not established |
| Host spool positions | Uses the supported AMS spool positions |
| Heat control | 35–70°C setting range |
| Printing while installed | Filament remains in the supported AMS setup |
| Humidity behavior | Humidity mode; confirm model-specific thresholds in manual |
| Loaded-material compatibility | Confirm AMS generation and every spool’s heat tolerance |
Creality Dry Box 2.0
Sovol SH03
SUNLU SP2
SUNLU S1 Plus